/*----------------------------------------------------------------------------*/
/* Copyright (c) FIRST 2008. All Rights Reserved.                             */
/* Open Source Software - may be modified and shared by FRC teams. The code   */
/* must be accompanied by the FIRST BSD license file in $(WIND_BASE)/WPILib.  */
/*----------------------------------------------------------------------------*/

#include "DigitalOutput.h"
//#include "NetworkCommunication/UsageReporting.h"
#include "Resource.h"
#include "WPIErrors.h"

/**
 * Create an instance of a DigitalOutput.
 * Creates a digital output given a channel. Common creation routine for all
 * constructors.
 */
void DigitalOutput::InitDigitalOutput(uint32_t channel) {
  m_table = NULL;
  char buf[64];

  if (!CheckDigitalChannel(channel)) {
    snprintf(buf, 64, "Digital Channel %d", channel);
    wpi_setWPIErrorWithContext(ChannelIndexOutOfRange, buf);
    return;
  }
  m_channel = channel;
  m_pwmGenerator = (void *)~0ul;

  int32_t status = 0;
  allocateDIO(m_digital_ports[channel], false, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));

  HALReport(HALUsageReporting::kResourceType_DigitalOutput, channel);
}

/**
 * Create an instance of a digital output.
 * Create a digital output given a channel.
 *
 * @param channel The digital channel 0-9 are on-board, 10-25 are on the MXP
 * port
 */
DigitalOutput::DigitalOutput(uint32_t channel) { InitDigitalOutput(channel); }

/**
 * Free the resources associated with a digital output.
 */
DigitalOutput::~DigitalOutput() {
  if (StatusIsFatal()) return;
  // Disable the PWM in case it was running.
  DisablePWM();

  int32_t status = 0;
  freeDIO(m_digital_ports[m_channel], &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));
}

/**
 * Set the value of a digital output.
 * Set the value of a digital output to either one (true) or zero (false).
 * @param value 1 (true) for high, 0 (false) for disabled
 */
void DigitalOutput::Set(uint32_t value) {
  if (StatusIsFatal()) return;

  int32_t status = 0;
  setDIO(m_digital_ports[m_channel], value, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));
}

/**
 * @return The GPIO channel number that this object represents.
 */
uint32_t DigitalOutput::GetChannel() const { return m_channel; }

/**
 * Output a single pulse on the digital output line.
 * Send a single pulse on the digital output line where the pulse duration is
 * specified in seconds.
 * Maximum pulse length is 0.0016 seconds.
 * @param length The pulselength in seconds
 */
void DigitalOutput::Pulse(float length) {
  if (StatusIsFatal()) return;

  int32_t status = 0;
  pulse(m_digital_ports[m_channel], length, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));
}

/**
 * Determine if the pulse is still going.
 * Determine if a previously started pulse is still going.
 */
bool DigitalOutput::IsPulsing() const {
  if (StatusIsFatal()) return false;

  int32_t status = 0;
  bool value = isPulsing(m_digital_ports[m_channel], &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));
  return value;
}

/**
 * Change the PWM frequency of the PWM output on a Digital Output line.
 *
 * The valid range is from 0.6 Hz to 19 kHz.  The frequency resolution is
 * logarithmic.
 *
 * There is only one PWM frequency for all digital channels.
 *
 * @param rate The frequency to output all digital output PWM signals.
 */
void DigitalOutput::SetPWMRate(float rate) {
  if (StatusIsFatal()) return;

  int32_t status = 0;
  setPWMRate(rate, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));
}

/**
 * Enable a PWM Output on this line.
 *
 * Allocate one of the 6 DO PWM generator resources from this module.
 *
 * Supply the initial duty-cycle to output so as to avoid a glitch when first
 * starting.
 *
 * The resolution of the duty cycle is 8-bit for low frequencies (1kHz or less)
 * but is reduced the higher the frequency of the PWM signal is.
 *
 * @param initialDutyCycle The duty-cycle to start generating. [0..1]
 */
void DigitalOutput::EnablePWM(float initialDutyCycle) {
  if (m_pwmGenerator != (void *)~0ul) return;

  int32_t status = 0;

  if (StatusIsFatal()) return;
  m_pwmGenerator = allocatePWM(&status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));

  if (StatusIsFatal()) return;
  setPWMDutyCycle(m_pwmGenerator, initialDutyCycle, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));

  if (StatusIsFatal()) return;
  setPWMOutputChannel(m_pwmGenerator, m_channel, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));
}

/**
 * Change this line from a PWM output back to a static Digital Output line.
 *
 * Free up one of the 6 DO PWM generator resources that were in use.
 */
void DigitalOutput::DisablePWM() {
  if (StatusIsFatal()) return;
  if (m_pwmGenerator == (void *)~0ul) return;

  int32_t status = 0;

  // Disable the output by routing to a dead bit.
  setPWMOutputChannel(m_pwmGenerator, kDigitalChannels, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));

  freePWM(m_pwmGenerator, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));

  m_pwmGenerator = (void *)~0ul;
}

/**
 * Change the duty-cycle that is being generated on the line.
 *
 * The resolution of the duty cycle is 8-bit for low frequencies (1kHz or less)
 * but is reduced the higher the frequency of the PWM signal is.
 *
 * @param dutyCycle The duty-cycle to change to. [0..1]
 */
void DigitalOutput::UpdateDutyCycle(float dutyCycle) {
  if (StatusIsFatal()) return;

  int32_t status = 0;
  setPWMDutyCycle(m_pwmGenerator, dutyCycle, &status);
  wpi_setErrorWithContext(status, getHALErrorMessage(status));
}

/**
 * @return The value to be written to the channel field of a routing mux.
 */
uint32_t DigitalOutput::GetChannelForRouting() const { return GetChannel(); }

/**
 * @return The value to be written to the module field of a routing mux.
 */
uint32_t DigitalOutput::GetModuleForRouting() const { return 0; }

/**
 * @return The value to be written to the analog trigger field of a routing mux.
 */
bool DigitalOutput::GetAnalogTriggerForRouting() const { return false; }

void DigitalOutput::ValueChanged(ITable *source, const std::string &key,
                                 EntryValue value, bool isNew) {
  Set(value.b);
}

void DigitalOutput::UpdateTable() {}

void DigitalOutput::StartLiveWindowMode() {
  if (m_table != NULL) {
    m_table->AddTableListener("Value", this, true);
  }
}

void DigitalOutput::StopLiveWindowMode() {
  if (m_table != NULL) {
    m_table->RemoveTableListener(this);
  }
}

std::string DigitalOutput::GetSmartDashboardType() const {
  return "Digital Output";
}

void DigitalOutput::InitTable(ITable *subTable) {
  m_table = subTable;
  UpdateTable();
}

ITable *DigitalOutput::GetTable() const { return m_table; }