diff --git a/sources/2890/canjectors.md b/sources/2890/canjectors.md
index 57dd2be..19f27bf 100644
--- a/sources/2890/canjectors.md
+++ b/sources/2890/canjectors.md
@@ -52,15 +52,19 @@ The schematic shows the "middle" Canjector variant with:
 
 ## Design Variants
 
-Chris designed three Canjector variants for different positions in the CAN bus topology:
+Chris designed five Canjector variants to form a complete CAN bus distribution system. All variants support configurable termination via a shunt jumper — populate the shunt to activate 120Ω termination at any position in the chain.
 
-| Variant | Position | CAN Termination | Notes |
-|---------|----------|----------------|-------|
-| **Start** | Bus origin (PDH side) | No termination at this end | Upstream CAN connector from PDH |
-| **Middle** | Intermediate nodes | Switchable 120Ω | 3 CAN connections + 12V passthrough |
-| **Major** | Bus terminus (end of line) | Fixed 120Ω termination | Final node — TERM switch, 120Ω resistor populated |
+| Variant | CAN connections | 12V outputs | Termination | Typical use |
+|---------|----------------|-------------|-------------|-------------|
+| **Start** | 1 | 1 | Shunt-activated | Bus origin at PDH |
+| **Minor** | 3 | 1 | Shunt-activated | Intermediate node |
+| **Middle** | 3 | 2 | Shunt-activated | Intermediate node + power distribution |
+| **Major** | 6 | 2 | Shunt-activated | End of chain (large node) |
+| **Endz** | 1 | 1 | Shunt-activated | Start OR final terminator — diagnostic USB interface |
 
-**Major variant:** Blue PCB, three identical sections, TERM label, 120Ω termination resistor visible, PWR LED, 2-pin header. This is the end-of-bus variant — fixed 120Ω termination resistor must be populated. Zip file in `canjector-gerbers/` directory.
+**All Canjectors share the same termination philosophy:** no fixed termination at any position. Use a shunt jumper to enable 120Ω termination exactly where the bus physics require it. This eliminates the need for separate "terminating" and "non-terminating" variants.
+
+**Endz** is unique — it's the diagnostic variant with a USB Type-B connector for direct laptop-to-CAN connection. Meant to serve as either the first or last device in the chain. Currently experiencing design problems; no working units on hand.
 
 ## Connection to Training
 
@@ -84,6 +88,10 @@ This is a **confidence builder** for the training vault — it shows Chris's pra
 |------|-------------|
 | `canjector-schematic.png` | Middle Canjector — EasyEDA schematic |
 | `canjector-start-pcb.png` | Start variant — PCB layout (red solder mask) |
-| `canjector-major-render.png` | Major variant — 3D render, blue PCB |
+| `canjector-minor-render.png` | Minor variant — 3D render, blue PCB |
+| `canjector-major-render.png` | Major variant — 3D render, blue PCB, 6 CAN ports |
+| `canjector-endz-render.png` | Endz variant — USB-to-CAN diagnostic interface |
 | `canjectors.md` | This documentation file |
-| `canjector-gerbers/` | Manufacturing files (Gerbers + drill files + How-to-order guide) |
\ No newline at end of file
+| `canjector-gerbers/` | Major variant manufacturing files |
+| `canjector-minor-gerbers/` | Minor variant manufacturing files |
+| `canjector-endz-gerbers/` | Endz variant manufacturing files |
\ No newline at end of file